Plumbing Basics: The First Step for Bathtub Installation
Plumbing Basics: The First Step for Bathtub Installation
Blog Article
The article listed below on the subject of Tools You Need to Install a New Bathtub is pretty much entertaining. You should give it a look.
Mounting a bath tub isn't exactly brain surgery, however it does need strong plumbing, woodworking, as well as sometimes, tiling abilities. Changing an old bath tub with a brand-new one is additionally a reasonably hard task. If the old bathtub is easily easily accessible, the task can move quickly; if you have to open up a wall surface to get rid of the old tub and place the brand-new bath tub, the task is a lot harder. In either situation, the project is within a residence handyman's abilities, although you will require a helper to move out the old bathtub and embeded in the new one. Make sure you have actually qualified on your own for the job as well as are comfortable trying it. Rather than working with a professional to take over a halfway-completed task, it is better to take into consideration utilizing one prior to you start. Chances are you may require an expert plumber to make tube links.
This post will certainly help you set up a new bathtub in your shower room if you have currently bought a brand-new tub as well as do not need to change the arrangement of your previous water supply pipelines.
Your devices and material checklist must consist of the following:
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your setup, then the first thing you need to do is separate the water system. After doing so, switch on the taps to drain pipes any type of water continuing to be in the system. The procedure of getting rid of the existing faucets can be quite troublesome due to the restricted access that is commonly the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the faucets. Have a cloth all set for the continuing to be water that will originate from the pipelines. Once the supply pipelines have been gotten rid of, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary faucets from transforming during this procedure. When the faucets have actually been removed, the holes in the bath/basin will need to be cleaned of any type of old securing substance.
Prior to moving on to fit the new taps, contrast the pipeline connections on the old taps to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly require a plastic port to stop damage to the string. One end of the port fits on the plastic tail of the tap as well as the various other end offers a link to the existent supply pipes.
If you require to fit a monobloc, after that you will require minimizing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, position the tap in the installing opening in the bath/basin ensuring that the washers are in location between the tap and the sink. Safeguard the tap in place with the supplier offered backnut. When the faucet is safely in position, the supply pipelines can be linked to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular faucet connectors. The former type must be connected to the faucet ends initially, tightening up only by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Installing the Bath tub
Utilizing both wood boards under its feet, position the bath tub in the required placement. The wooden boards are useful in evenly spreading the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four little factors.
The next objective is to ensure that the bath tub is leveled all round. This can be achieved by inspecting the level as well as changing the feet on the bathtub up until the spirit level reviews degree.
To set up faucets, fit all-time low of the outermost versatile faucet port to the suitable supply pipe by making a compression join; after that do the exact same for the other tap.
Switch on the water and also inspect all joints and brand-new pipework for leaks and tighten them if essential. Fill the bathtub as well as likewise inspect the overflow electrical outlet as well as the typical outlet for leakages.
Lastly, take care of the bath paneling as defined in the supplier's instruction manual. Tiling and also securing around the bathtub needs to wait up until the bath tub has been made use of a minimum of once as this will certainly settle it right into its final placement.
Getting ready for the Installment
To start with, the supporting framework provided with the bath must be fitted (if needed) according to the producer's guidelines. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is important to make sure that if the tap features a plastic washer, it is fitted between the bath as well as the taps. On a plastic bathroom, it is also practical to fit a supporting plate under the taps unit to prevent strain on the tub.
Fit the flexible faucet adapters to the bottom of both faucets making use of 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Ensure you utilize every one of the provided washers.
Attach the catch to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its last placement.
Tiling Around the Bathtub
In the location where the bath meets the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the installation can move enough to split a rigid seal, causing the water to penetrate the wall surface in between the bathroom and the tiling, resulting in problems with dampness and also feasible leakages to the ceiling below.
You can select from a variety of coloured sealants to blend in your fixtures and also fittings. They are sold in tubes as well as cartridges, as well as are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a larger void to fill, you can load it with spins of drenched newspaper or soft rope. Keep in mind to always fill the bath tub with water before sealing, to permit the motion experienced when the tub remains in use. The sealer can split relatively very early if you do not take into account this activity before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily offered on the marketplace. It is a good idea to fit the floor tiles using water-resistant or water-proof glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you like reading up on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Post a remark below. We'd be pleased to know your opinions about this article. Hoping that you visit us again in the near future. Do you know about another person who is very much interested in the topic? Why not share it. Thanks a lot for going through it.
Save your home, call now! Report this page